Rust-Oleum 9100 WG Wintergrade Low Temperature Epoxy (2025)

Skip to product information
  • Rust-Oleum 9100 WG Wintergrade Low Temperature Epoxy (1)

1 / of 2

Rust-Oleum 9100 WG Wintergrade Low Temperature Epoxy

Brand: Rust-Oleum

Two pack epoxy system for high performance and maintenance. 4.5 litres

Categories: Building Repair, Floor Coatings, Floor Paints and Floor Coatings, Maintenance, Rust-Oleum, , Two-Component Floor Coatings

Buy Now

  • DESCRIPTION
  • Related Products
  • Datasheet
  • Reviews

DESCRIPTION

Rust-Oleum 9100 WG Wintergrade Low Temperature Epoxy is a two pack high performance epoxy system for high performance and maintenance. It is a Wintergrade low temperature version of Rust-Oleum 9100.

  • Pack Size: 4.5 litres

Product Description

A higher solids, improved coverage and lower VOC content product than the standard 9100 Epoxy. A two-pack, gloss epoxy coating for metal, walls and floors. The most efficient epoxy system providing a very hard coating with high layer thickness for lasting results even with a single coat application. Ideal as a glossy floor paint for garages, warehouses, indoor car parks etc. With optimal protection achieved in only one or two applications.

Product Benefits

2x thicker than regular epoxies (125 micron dry) Very resistant against abrasion and chemicals Contains a high amount of rust inhibitors Can be applied on metal and floors Tint-able in almost any colour

Recommended Use

9100 Topcoats are designed for application on manually prepared rusted steel surfaces and can also be used on clean, blasted steel, primed steel, concrete and previously coated surfaces. 9100 Topcoats offer appropriate protection against strong chemicals, acids, alkalis and solvents; frequent product spillage and chemical cleaning; high humidity and moisture conditions.

Recommended System

Primers

  • 9100 Topcoats can be applied on cleaned, sound mineral substrates, sound, well prepared previous coatings
  • Porous substrates should be primed with 5401 or 5421Impregnation Primer
  • Very dense substrates, like ceramic tiles, should be primed with Super Adhesive 3333 or 3366
  • 9100 Topcoats can be applied directly on 9170/9180 Metal Primers or 9169 Epoxy Rust Primer

Topcoat

If good U.V. resistance is required Polyurethane Topcoats 9200 or 9600 should be applied (except for the clear coatings).

Surface Preparation

Remove grease, oil and all other surface contaminations by alkaline or high pressure (steam)cleaning in combination with appropriate detergents. Sand previous coatings, which are in good condition to remove gloss and to roughen the surface slightly, check compatibility. The surface must be clean and dry during application.

Steel

Remove loose rust, mill scale and deteriorated coatings by hand or power tool cleaning to St 2/3 (ISO 8501-01 : 1988). Large areas may be brush-off blasted to Sa 2 (ISO 8501-01: 1988), blast profile max. 50 µm. For immersion purposes, prepare to Sa 3 (ISO 8501-01 :1988), blast profile max. 75 µm.

Concrete and masonry

New concrete or masonry should cure and dry for at least 30 days before applying the coating system. Remove laitance, any loose or unsound concrete ordeteriorated coatings. Smooth concrete should be roughened.

Directions forUse

Base 9100 + Activator 9101: Standard grade Base 9100 + Activator 9101HS: High Solids grade Base 9100 + Activator 9101WG: Winter Grade, application at low temperature

  • Stir individual components thoroughly before mixing them together
  • Use a mechanical low speed mixer
  • Mix the product carefully during 3 minutes
  • Temperature of the mixedmaterials should be at least 10°C

Application Conditions

Temperature of air and substrate between 10 and 35°C (for the 9100/9101WG between 0 and 15°C) and relative humidity below85%. The substrate temperature must be at least 3°C above dew-point.

Application and Thinning

Brush

Use natural bristles, long hair brushes. Dilute up to 10% volumewith Thinner 160 (do not dilute 9101HS). Preferably use disposable brushes.

Roller

  • Use a medium nap polyamide 16-20 mm rollers
  • Roller application requires 2 coats to achieve recommended d.f.t.
  • Dilute up to 10% volume with Thinner 160 (do not dilute 9101HS)
  • Preferably use disposable rollers.

Airless Spray

  • Tip size: 0.013-0.021 inch
  • Fluid pressure: 150 - 225 bar
  • Avoid excessive film thickness
  • Up to 10% volume Thinner 160 (do not dilute 9101HS)

Air-Atomised Spray

Not recommended.

Cleanup

Rustoleum Thinner 160.

Contact Us

For further advice regarding the use of this product, technical support or a quotation please contact us.

Buy Now

Related Products

  • PPG Sigma Anti-Slip Aggregate Fine Fine grade aggregate for anti-slip. 5.56 litres
  • PPG SigmaCover 2 A two-pack, high solids, fast drying epoxy coating offering great adhesion, even at low temperatures. Formerly Amerlock 2, PPG SigmaCover 2 is ideal for steel and concrete even down to temperatures as low as 0°C, with fast drying properties.
  • Jotun Jotamastic Smart Pack A two-component surface tolerant, high solids epoxy mastic coating for general and marine use.Pack Size: 10 litres
  • Jotun Thinner No. 17 Thinner designed to improve the flow of a range of Jotun epoxy products. Also for cleaning pumps and tools before and after painting.

Reviews

There are no reviews yet.

Download datasheet

Rust-Oleum 9100 WG Wintergrade Low Temperature Epoxy (2025)
Top Articles
Latest Posts
Recommended Articles
Article information

Author: Lakeisha Bayer VM

Last Updated:

Views: 5292

Rating: 4.9 / 5 (49 voted)

Reviews: 88% of readers found this page helpful

Author information

Name: Lakeisha Bayer VM

Birthday: 1997-10-17

Address: Suite 835 34136 Adrian Mountains, Floydton, UT 81036

Phone: +3571527672278

Job: Manufacturing Agent

Hobby: Skimboarding, Photography, Roller skating, Knife making, Paintball, Embroidery, Gunsmithing

Introduction: My name is Lakeisha Bayer VM, I am a brainy, kind, enchanting, healthy, lovely, clean, witty person who loves writing and wants to share my knowledge and understanding with you.